MTN6303-0019 Schneider KNX Mini presence detector Introduction：
KNX presence detector for inconspicuous installation in suspended ceilings.
The presence detector detects the presence of persons even in the case of small movements.
Control of the lighting is carried out dependent on movement (4 channels) or additionally dependent on brightness (1 channel) via KNX telegrams. If there is sufficient daylight, the lighting is switched off or adapted to a detection brightness (constant light regulation).
Devices for heating, ventilation or air conditioning (HVAC) can also be controlled (1 channel).
The presence detector has four detection sensors (passive infrared), a brightness sensor, an IR receiver and an LED to indicate a detected movement, in test mode indication of the activated programming mode.
The presence detector can be used as a single detector or in master-slave mode. The setting is carried out in the ETS.
The presence detector can also be set and tested without the ETS, but with the appropriate remote control (available as an accessory).
Indoor installation in suspended ceilings The detector is installed with a retainer spring in a circular aperture (diameter 35 mm) in a suspended ceiling (e.g. plasterboard). The minimum installation depth is 65 mm.
MTN6303-0019 Schneider KNX Mini presence detector Description：
Schneider Electric KNX presence detector MTN6303-0019 is in color white with frontal, lateral detection sensor. This presence detector mounting mode can be both ceiling and flush mounted. The protection type is creep zone protection, improving safety level. Being made of plastic material, this presence detector is quite reliable and resistant. And it features protective untreated surface treatment. And it is mercury free and heavy metal free, which takes care of the environment and your health as always. KNX combines all main building functions like lighting, heating, air-conditioning or shading into one intelligent system, resulting in considerable energy savings, and save installation time.
KNX software functions:
Movement detection: The detected presence of a person is signalled using a KNX telegram. Lighting control: The room lighting is controlled depending on movement and brightness. If there is sufficient daylight, the lighting is switched off or dimmed to a constant level. Basic lighting: Activates basic lighting after the overtravel time has elapsed, either for a limited time or dependent on the brightness. HVAC control: Devices for heating, ventilation, air conditioning (HVAC) are switched from energy-saving mode to comfort mode dependent on movement. Operating modes: Single detector, Master, Slave, Master in parallel operation. Master: Controls the lighting and HVAC system. Additional detectors as slaves increase the area of detection. Slave: Only detects movement in its area and sends the information to the master. Master in parallel operation: Controls the lighting in its area (can be expanded with additional detectors as slaves). The only master in the installation only controls the HVAC system for the entire area. 2 logic gates.
MTN6303-0019 KNX Presence detection Specifications：
Colour tint：polar white
Art. no : MTN6303-0019
Range of product : KNX
Product or component type：Presence detector
Complementary:
Device presentation：Complete product
Number of levels: 6
Protection type：Creep zone protection
Type of setting：Light sensitivity adjustable/Time adjustment
Detection face：Frontal: 3 m/Lateral: 3 m
Surface treatment：Untreated
Device mountin：Flush/Ceiling
Sensors: 4 x passive infrared
Duty cycle：15300 minutes
Time setting: 60 s – 255 min.
Number of zones: 136 with 544 switching segments
Time delay range：0…1 s (switch-on)
Range: max. 6 x 6 m (tangential) max. 4 x 4 m (radial)
Mounting height: 2 – 5 m
Detection angle：360° horizontal
Device mounting：Flush
Optimal mounting height: 2.8 m
IP protection rating: IP 20
Packing Units：
Unit Type of Package 1：PCE
Number of Units in Package 1：1
Package 1 Height：9.0 cm
Package 1 Width：7.5 cm
Package 1 Length：12.0 cm
Package 1 Weight：92.0 g
